Skip to content

Know every line of your repair before we start

(559) 552-7713
(559) 552-7713
Silver sedan with crushed rear quarter clamped to a red frame machine, chains running to a blue pulling tower, technician working beside it in a shop bay

ServicesFrame Straightening

Frame Straightening in Sanger

Even when the outside of your car looks like a simple fix, a collision can bend the structure beneath it. We measure the frame against factory dimensions, show you which points moved, and lay out the repair plan and its cost drivers before your vehicle goes on the rack.

What frame straightening fixes

Most cars and crossovers built today are unibody, with the body and frame welded into one shell. Pickups and many SUVs are still built on a separate ladder frame. On both designs, an impact can move rails, aprons or the floor pan a fraction of an inch out of place, and that small shift is enough to throw off alignment, panel gaps and how crumple zones would behave in a second crash.

Frame straightening uses a frame rack, chains and controlled hydraulic pulls to move the structure back to the manufacturer's published measurements. It is the right call when the damage is in the bones of the vehicle and the metal can still be returned to spec. When a section is kinked or torn rather than bent, we tell you plainly that it needs to be replaced instead of pulled.

Before anything is pulled, you get a written estimate that lists what we measured, what we plan to do and which parts are likely to need replacing. If the job changes once panels come off, we call you first.

Estimator photographing a gray SUV's crumpled hood and bumper with a tablet as the owner watches, outside open body shop repair bays

What the work includes

  1. 01

    Electronic measuring

    We check dozens of reference points under the vehicle and compare them to factory dimensions. You see which points are out and by how much, so the repair is based on numbers, not guesswork.

  2. 02

    Anchoring on the frame rack

    Your vehicle is clamped at its pinch welds or frame mounts so pulls go exactly where they are aimed. Good anchoring keeps us from stressing parts of the structure that were never damaged.

  3. 03

    Controlled pulls and re-measuring

    We pull in stages and measure between each one. Metal has memory, so slow, measured pulls bring it back without stretching or cracking it.

  4. 04

    Sectioning or replacing damaged parts

    Rails or supports that are creased too sharply to straighten are cut out and replaced following the maker's repair procedures. Whenever we can spot this ahead of time, it goes on the estimate up front.

  5. 05

    Alignment and refit checks

    After the structure is right, we check suspension mounting points, wheel alignment and the gaps around doors, hood and trunk. Those gaps are a quick way for you to see the repair landed where it should.

  6. 06

    Refinishing what was disturbed

    Welded or heated areas get corrosion protection and any outer panels are painted to match. We are PPG certified, and that refinishing work is part of the same estimate.

Questions about Frame Straightening?

Call(559) 552-7713

Signs your car may need frame work

  • It pulls or will not stay aligned

    If your car drifts after a crash, or an alignment does not hold, the suspension mounts may have moved with the frame.

  • Uneven gaps around doors or hood

    A wider gap on one side, or a door that suddenly needs a slam to latch, often points to a shifted structure rather than a bent panel.

  • Tires wearing on one edge

    Fast, uneven wear after an accident is a common clue that the wheels are no longer sitting where the factory put them.

  • Creases under the car

    Wrinkles in the floor pan, rails or wheel wells are worth a look, even if the outside seems fine.

  • New squeaks, rattles or wind noise

    When the body is slightly out of square, seals stop meeting and parts rub. It is easy to dismiss, but it is often structural.

How a frame repair goes at our shop

  1. 1

    You bring your vehicle in

    We walk around it with you, hear what happened and ask how it has been driving since. Then we put it up and measure.

  2. 2

    Written estimate before work

    You get the scope on paper: which points are out, what we will pull, what may need replacing and the main cost drivers. Nothing starts until you have read it and said yes.

  3. 3

    Teardown and a second look

    Damaged panels come off so we can see the full structure. If we find something the first inspection could not show, we stop and call you with an updated estimate before doing extra work.

  4. 4

    Pull, measure, repeat

    The structure is straightened in stages until every reference point is back within spec. We keep the final measurements so you can see the result.

  5. 5

    Reassembly and road test

    Panels go back on, refinishing is done, alignment is set and we drive the car to make sure it tracks straight before we call you to pick it up.

What affects the cost of frame straightening

Frame work is priced by how far the structure moved and what it takes to bring it back, so two cars with similar dents can land in very different places. Your estimate spells out each of these factors for your vehicle. If the repair turns out to be larger once we look inside, you hear about it from us before any added work happens.

Where the damage is
A bent front rail is a very different job than a pushed-in pillar or a buckled floor. Damage near the passenger area usually takes more time and care.
Unibody or full frame
Unibody cars often need sectioning and welding, while a truck frame may straighten with pulls alone. The construction of your vehicle shapes the method.
Parts that must be replaced
Some metals, especially high-strength steels, cannot be heated or pulled past a certain point and must be replaced. Part availability affects both cost and timing.
Related suspension and refinish work
Bent control arms, alignment and painting the panels around the repair all add to the total and are listed separately so you can see each one.

Frame straightening questions

Is a car with frame damage safe once it is fixed?

Yes, when the structure is measured back to factory specifications and any parts that cannot be straightened are replaced. That is why we measure before, during and after the pulls. If we ever think a structure should not be repaired, we will tell you directly.

Does frame damage mean my car is totaled?

Not necessarily. Many vehicles with frame damage are repaired every day. Whether an insurer totals a car depends on repair cost compared to its value, which is a decision the insurance company makes. Our estimate gives them and you a clear picture to work from.

How long will my vehicle be at the shop?

It depends on how much the structure moved and whether parts need to be ordered. Once we have measured and torn down the damaged area, we can give you a realistic timeline and keep you posted if it changes.

Will my car drive the same afterward?

That is the goal of the whole process. After straightening we set the alignment and road test it to confirm it tracks straight and the doors and panels fit as they should.

Can you help if insurance is paying for it?

Yes. We send the insurer the same detailed estimate you get, plus measurements and photos of what we found. Our Insurance Claims page explains how we work alongside your adjuster.

Dark blue sedan parked on a concrete lot in front of open body shop bays with plastic-masked cars and tool carts inside

Find out what is really going on underneath

Bring your vehicle in and we will measure it and walk you through the findings. You will have the repair plan in writing before anything is pulled.