Skip to content

Know every line of your repair before we start

(559) 552-7713
(559) 552-7713
Technician using an orbital sander on a cracked gray primed bumper cover resting on a rolling stand in a body shop bay with a lift and car behind.

ServicesBumper Repair

Bumper Repair in Sanger

A scraped corner or a cover hanging loose after a parking lot bump is one of the most common things we see. We look behind the plastic, tell you whether it can be repaired or should be replaced, and write it all down before any work begins.

What bumper repair covers

The painted part you see is usually a plastic cover. Tucked underneath is a foam or plastic absorber that soaks up low-speed hits, a stiff bar of steel, aluminum or composite that does the structural work, and the clips, brackets and tabs that hold it all in place. On many newer cars the cover also carries parking sensors or the radar behind adaptive cruise and blind spot alerts.

A light tap can leave the outside looking fine while a tab snaps or the absorber cracks. When there is any doubt, we take the cover off, so the estimate reflects what is really damaged and not just what shows.

Smaller jobs, like a scuff or a short crack, can often be repaired and refinished. A torn cover, a crushed bar behind it or broken sensor mounts usually points to replacement. Either way, you see our reasoning on paper before you decide.

What's included in the repair

Behind-the-cover inspection
We check the absorber, reinforcement bar, brackets and clips for cracks or bends. Anything we find goes on the estimate with a note on why it matters.
Plastic welding and crack repair
Many covers are made of polypropylene or similar plastics that can be welded from the back and reinforced. We sand, fill and shape the area so the repair stays flexible and holds its contour.
Tab and mount repair
Broken mounting tabs are the reason a lot of bumpers sag or leave uneven gaps. We rebuild or replace them so the cover sits flush with the fenders and lights.
Refinishing that flexes with the plastic
Raw plastic needs an adhesion promoter, and the paint needs to bend without cracking. As a PPG certified shop, we mix and match the color to your car and blend it into nearby panels when that gives a cleaner result.
Sensor checks
If your bumper carries parking sensors or radar, we confirm they are seated and working before you pick up the car, and we tell you up front if a calibration is needed.

Signs your bumper needs attention

  • Uneven gaps at the fender or headlight

    A gap that is wider on one side usually means a broken clip or tab. Left alone, the cover can work loose at highway speed.

  • Cracks or paint lifting near a corner

    Paint that flakes off plastic often hides a crack underneath. Strong Central Valley sun tends to make small cracks spread faster.

  • A cover that moves when you push it

    A solid bumper should not flex or rattle by hand. Movement points to damaged brackets or a loose reinforcement.

  • Sensor or driver-assist warnings

    A parking sensor that beeps constantly, or a blind spot light that stays on after a bump, can mean a sensor was knocked out of position.

  • Deep scrapes down to raw plastic

    Gray or black plastic showing through means the finish is gone in that spot. It will keep peeling until the area is properly refinished.

How your bumper repair goes

  1. 1

    Talk it through and bring it in

    Give us a call and tell us how the damage happened. We'll pick a day that works for you to drop your vehicle off so we can see it in person.

  2. 2

    Inspection and written estimate

    We look the bumper over, and remove the cover if needed, to see the parts behind it. You get a written estimate listing each repair, part and refinish step, and we go over it with you so nothing is a mystery.

  3. 3

    Repair or replace

    Once you approve the estimate, we weld and reshape the cover or fit a new one, along with any brackets, clips or absorber parts that were damaged. If we find something unexpected, we stop and call you before doing more.

  4. 4

    Paint, reassembly and checks

    The bumper is primed, painted and cured, then mounted and lined up with the fenders and lights. We test sensors, wash the car and walk you around it when you pick it up.

Estimator photographing a gray SUV's crumpled hood and bumper with a tablet as the owner watches, outside open body shop repair bays

What affects the cost of bumper repair

Two bumpers that look alike from the curb can price out very differently once the cover is off. These are the things that move the number most. Each one is spelled out on your estimate so you know exactly what you are paying for.

Repair versus replacement
Short cracks and scuffs are usually cheaper to repair. Long tears, missing pieces or many broken tabs often make a new cover the better value.
Hidden parts behind the cover
A cracked absorber, bent reinforcement or broken brackets add parts and labor. We list them separately so you can see each one.
Sensors and calibration
Bumpers with parking sensors or radar take more care to remove and refit, and some systems need calibration after the repair.
Paint and blending
Metallic and tri-coat colors take more steps to match. Blending into the fender or quarter panel adds time but avoids a visible line.

Bumper repair questions

Something not covered here? (559) 552-7713

Can my cracked bumper be repaired, or do I need a new one?

It depends on the size and location of the damage. Cracks away from mounting points and sensors can often be welded and refinished. If the cover is torn through, warped from heat, or broken around several tabs, replacement is usually the sounder choice. We show you what we found and explain the reasoning in the estimate.

How do you get the color right on a plastic bumper?

Your car's paint code is the starting point for the formula. Before anything goes on the bumper, we spray a test card and hold it up to your existing finish in good light, then adjust if it is off. Plastic and steel can take the same color a little differently, so blending into the fender beside it is often part of the plan, and that step shows up on your estimate.

Should I go through insurance for a bumper?

Sometimes the repair costs less than your deductible, and paying directly makes more sense. Our written estimate gives you a clear number to compare. If you do file, our insurance claims page explains how we work with your adjuster.

My bumper looks fine but the parking sensor acts up. Is that a bumper job?

Often, yes. A bump can push a sensor out of its mount or crack the bracket that holds it, even with little visible damage. We check the mount and the sensor and let you know what it will take to fix it.

Do you handle damage beyond the bumper?

Yes. If the hit reached the fenders, lights or frame, we cover that through our collision repair and frame straightening work, and it all goes on one estimate.

Dark blue sedan parked on a concrete lot in front of open body shop bays with plastic-masked cars and tool carts inside

Let's get your bumper back in shape

Tell us what happened and bring your car by. We will look behind the cover and give you a written estimate before any work starts.